Formax Payout Program – Through Feb 29 2016

Now through February 29 2016, Formax is providing an additional discount between $50.00 and $300.00 off select products. Symco Group is passing these savings through to our customers.

For more information or to buy a new Formax solution, please contact Symco Group at 800-878-8002 or email us at info@symcogroup.com.

  • Formax Folders:
    • Formax Atlas – Additional $300 discount
    • Formax AtlasAS – Additional $300 discount
  • Booklet Finishers:
    • Formax Square IT – Additional $150 discount
  • Formax Cut-True Guillotine Cutters:
    • Formax Cut-True 13M – Additional $50 discount
    • Formax Cut-True 15M – Additional $100 discount
    • Formax Cut-True 16M – Additional $100 discount
    • Formax Cut-True 22S – Additional $100 discount
    • Formax Cut-True 27S – Additional $300 discount
  • Formax Creasers and Perforators:
    • Formax FD230 -Additional $100 discount
    • Formax FD90 – Additional $100 discount

Notes: Discount will be applied to purchase price.

New Accufast Tabbers available through Symco Group

Looking to add, upgrade or replace your tabbing solution? Symco Group is an authorized reseller for Asmarc Accufast for their complete line of Addressing Printers, Tabbers, Labelers, Affixers and more. Contact Symco Group today (info@symcogroup.com or 800-878-8002) to purchase your next tabbing solution.

Asmarc Accufast manufacturers several models to fit all your needs.

Accufast ET:

Accufast ET

Tabs both booklets and self mailers in the correct spots automatically. Very little setup or operator interaction is required. Select the correct tab mode, load the proper tabs and feed pieces from whatever device you choose on the front end. When full, just clean out the waste and splice on another strip of tabs and go.

Accufast KT:

Accufast KT

Table top tabber that applies either a 1″ or 1.5″ tab at speeds of 15,000 per hour. The KT is a crash tabber module and must be used with a feeder. The KT is the entry level for a professional level tabbing solution. By combining the KT with an FX feeder and CS3 output conveyor it creates a robust tabbing solution for your business needs.

Accufast KT2:

Accufast KT2

The KT2 is the “big brother” to the KT. The KT2 takes care of twin tab requirements on thin forms in a single pass. Each tabbing head works independently of the other as they apply tabs to the leading edge of the pieces moving through the machine.

Accufast Freehand Tabber:

Accufast FreehandTabber

Simple unit with a built in feeder. The Freehand Tabber uses crash tab technology in which a tab is ejected in front of the piece and the piece crashes into it carrying the tab and the piece between a set of rollers where the tab is folded and sealed. The Freehand tabber is a perfect machine if you are only tabbing a few mailers and need a machine to get it done quickly.

Accufast Slim Jim System:

accufast KT_ET_HDF_inline5-2011_2

The Slim Jim system is the combination of the of the KT 1.5″ tabber running inline with the Accufast ET. The Accufast Slim Jim allows you to get the extra tab on a side at right angles to the initial side as it runs the piece through the ET and into the KT.

Accufast LDM:

Accufast LDM

Until now rolled tabs were available on either small (5-10,000) or large (40,000) tabs per roll. The small rolls were always running out and the large rolls were hard to handle. Either way, production suffered. The ACCUFAST LDM handles rolls of at least 75,000 tabs and delivers the tabs to the tabber smoothly and automatically. The rolls are easy to handle and rolls may be spliced one to the other to avoid rethreading (another production killer). Tabs are wound on a spool which simplifies handling and increases the tab count per roll. An adapter kit allows he LDM to be set up to run pancake rolls of less than 12 inches in diameter. This allows a mailer to use up his supply of old tabs prior to switching to the ACCUFAST spooled tabs.